The exterior of the car is the bit that people are most likely going to see, and it is the bit you will see as yo walk towards the car in the morning, so you want to make sure it is in a condition you are proud of and want to look back at every time you park up and get out. You want to make sure that your car is properly prepared for other detailing processes. If you haven’t washed all the panels and removed all the dirt from it you risk causing more damage to the car then you do good. If there are already large scratches and blemishes in the paint work and they can’t be remedied using the following steps, you might want to consider paint correction first. This will restore the paint and remove any of those nasty marks. So if you haven’t yet, you should definitely give that a read first to make sure it is done right and the car is perfectly set to be further detailed. Cars that have a vinyl wrap can still be detailed. If the job has been done professionally then you won’t see any joins in prominent areas of the body panels and you can still detail it as you would the factory paint finish. When it comes to exterior vehicle detailing you can break it down into 5 distinct categories;
- Claying
- Waxing
- Polishing
- Wheel and Brake Detailing
- Glass Detailing
Top tip! When detailing, try to do it out of strong direct sunlight, if the car is left in the sun the paint can soften and there is a greater risk of damaging the paintwork.
1. Claying
Your car comes under attack from so many different particles and elements while it is out on the road; from acidic rain to grit to exhaust fumes, the paintwork is never left alone. So it is essential that you maintain it well and follow as many of these steps as you can to protect it. To see just how contaminated and dirty the paintwork is there is a simple test. Once you have washed and dried your car get a plastic sandwich bag and put your hand in it, then lightly stroke your hand over the paintwork. If it feels rough and bumpy the paint is contaminated and needs to be clayed.
Here are a few products we would recommend when it comes to claying your car.
- Paint Rubber – Clay Bar
- 3M Cleaner Clay
- Turtle Wax Refine & Shine Clay Bar Kit
An average vehicle needs to be clayed twice a year and a clay bar will last you somewhere between 18 – 24 months. If you buy a larger clay bar it is worth cutting it into quarters and storing 3 quarters of it in a case with lubricant in, this helps it last longer and you can use up one piece at a time. Make sure you buy clay bar lubricant instead of using water, water doesn’t offer as good a finished and can show small cloudy water marks on the paintwork afterwards. When you start claying follow the same procedure as you did when preparing the car, start from the top and work your way down. You should only clay your car after you have washed and dried it properly.
Spray a small area with the clay lubricant before gently rubbing the clay bar across the wetted area. You want to keep rubbing this area until to slides smoothly across the paint surface, if it sticks slightly there is still dirt to be removed.
Once the clay bar slides freely over the car panel you need to remove the lubricant residue with a microfibre cloth. Once you have dried the surface over run your fingers over it and if it feels smooth the work is done, if not then reclay it.
Move onto the next area of the car and repeat the two steps mentioned above until the whole car is spotless, smooth and clear of all dirt. If you have clayed your car you need to wax it afterwards to seal the paintwork and any slight holes left from the removed dirt.
Clay bar can be used on pretty much any surface of the car, so you can clay any chrome or glass too.
2. Waxing
To wax your car you need to make sure that the car is dry and you have clayed it first. Once you have done this you can choose your wax and get a foam pad to apply it with.
You only need a small amount of wax, which should be applied in overlapping circular wipes over the car in roughly half a metre square sections. You want to apply a thin layer of wax, too much and it will gunk up and leave clumps.
Apply slight pressure on the pad, enough that the wax comes off and bonds with the surface of the paintwork. Thinner layers are better as they are smoother and it looks far better once polished as it the thin film alloys the paint to shine through.
3. Polishing
When it comes to polishing you can either use an orbital buffer or hand polish the car, it is one of the finishing steps when detailing a car as it really makes the paintwork shine and sparkle. If you choose to use an orbital buffer make sure you don’t apply too much pressure as you don’t want to cause any damage to the cars paintwork.
The other is to get some car paint polish and work that into the paintwork instead. The difference between the two is that the polish needs a bit more pressure applied to it to cause more friction. This in turn breaks down any abrasive substances on the paint and adds shine to it.
If you polish by hand you want to get a microfibre cloth, folded to fit your hand, applying a small amount of polish to it before you start. You need no more than a 50 pence piece sized amount of polish on the cloth.
The technique is much the same as waxing your car, small overlapping circular motions in half a metre square sections. Keep rubbing the polish into this area until it turns clear, if you can still see any cloudiness or marks it needs to be worked into the paintwork further.
If you are new to car detailing and polishing we would recommend that you start by hand polishing and as you gain confidence you can think about machine polishing.
4. Wheel and Brake Detailing
The wheels and brakes may seem like a small bit of detailing but they actually make one of the biggest differences. If the rest of the paintwork is spotless but the wheels are dirty then the whole car looks much duller. If the wheels look bright and clean too then the whole car is much more of a head turner, plus, if you have gone to all the effort detailing the paintwork you may as well go the extra mile and finish the last little bit!
The wheels need to be inspected before they are detailed. If they have deep scrapes and scratches in the alloy it is worth getting them reconditioned first. There is not a huge amount of point detailing already damaged wheels as they aren’t going to look as smart as you would like due to the marks on them.
If the surface of the alloy is smooth and as very few deep scratches in it then you can begin to detail them. Detailing wheels is one of the most straight forward parts of vehicle detailing, you simply need a bit of older clay bar and lubricant again. Repeat the same steps mentioned in the Claying section of this blog and your wheels will look instantly brighter and cleaner.
It is worth protecting the alloy with wax again, just so any slight holes left by the dirt in the wheels doesn’t get further contaminated.
The brakes don’t have to be done as they are harder to reach, or you may even need to remove the wheel in order to get to the brakes properly.
Use brake cleaner to wipe the brake discs over to remove any brake dust, and while preparing the car ready to be detailed, make sure you wash the calliper well. You can hand polish it if you wish but a wash should be enough for the brakes.
Extra Detail: Tyre Dressing
Some detailing sites will tell you not to use tyre dressing as it can flick onto the wheel arches, leaving slight blemishes but others will tell you it is a good idea to dress your tyres. Dirty tyres make an otherwise clean car look dull, but by applying just a little bit of tyre dressing to them to restore them back to that glossy showroom black finish.
5. Glass Detailing
Glass detailing not only makes your car look better, but it helps improve your driving vision too, so it is a win-win when it comes to this stage of detailing.
Make sure that the car is out of the sun again and all of the glass surfaces are dry. If it is too hot the cleaner solution can pretty much evaporate before it hits the glass or can leave dry marks.
Spray the cleaning fluid onto the window and quickly scrub in a circular motion using the microfibre cloth. Once the glass is clean get a second, dry cloth to buff the window with to remove any last water spots and streaks.
Glass cleaner can also be used on the headlights, tail lights and mirrors. Just make sure that when you detail this elements of your car you properly dry them as any remaining residue can mist up inside a headlight or behind a mirror, ruining all your hard work.